Sonoma SGR30LP Grill Parts

Sonoma SGR30LP

Sonoma 30" Platinum Edition LP gas grill

Highest quality replacement parts for your Sonoma SGR30LP - Free USA shipping $49 or more* - No Sales Tax*

Sonoma SGR30LP owners manual and diagrams

Diagrams & owners manual not available for grill model# SGR30LP. If you have a manual you're willing to share, please click here to send us an email with the attached manual. Thank You!

Replacement grill parts for Sonoma model: SGR30LP

This page shows all of the parts we know fit model Sonoma SGR30LP. If the part you need is not shown below, try clicking the appropriate category button on the right side of the page. For example, if your looking for a burner and there are none here, click the burner button to see all the burners we have for Sonoma grills. You will need to know the dimensions of your existing grids to help you find the right part.

To get the correct Sonoma SGR30LP BBQ parts

You should measure your existing parts and compare them to what we show here. This is best done with them removed from the grill.
Verify your Sonoma model number by checking the CSA appliance tag on your grill to make sure you have the correct model number. Do not rely solely on the owners manual as these are frequently mixed up at retail stores when the grills are assembled. You'd be surprised at how many folks have the wrong owners manual.

SGR30LP Burners

CLA-BL0229

Click for photos

304 Stainless steel infrared rear rotisserie burner with ceramic wafer for Sonoma model SGR30LP. For use with both liquid propane (LP) and natural gas grills. 8,000 BTU. Orifice not included. Use old orifice or purchase our orifice part# CLA-VB0245 that can be drilled for LP gas or natural gas.

Dimensions:

Maximum overall length, including mounting tab on one end: 17”
Maximum width: 3 3/8”
Burner box 15 3/8” x 3 3/8”
Mounting holes: 16 1/8” on center

Part Number: CLA-BL0229
Dimensions: 3 3/8” x 17”
Material: stainless steel and ceramic
Weight: 3.0

SONT3

Click for photos

Stainless steel triple burner assembly set for Sonoma model SGR30LP.

Part Number: SONT3
Dimensions: 17 13/16” x 18 1/2”
Material: stainless steel
Weight: 1.6

==> All Sonoma Burners.

SGR30LP Burner Brackets and Carryovers

CLA-MS0116

Click for photos

Stainless steel Z-Bar burner support bracket. Made in USA
This part is currently out of stock, but more are already on the way and expected to arrive mid May

Part Number: CLA-MS0116
Dimensions: 2” x 23”
Material: stainless steel
Weight: 0.70

==> All Sonoma Burner Brackets and Carryovers.

SGR30LP Cooking Grids

53S33

Click for photos

Stainless steel cooking grids with solid 1/4” rods (set of 3) for Sonoma model SGR30LP.

Part Number: 53S33
Dimension Front-to-Back: 17 1/2”
Dimension Side-to-Side: 27 3/8”
Material: stainless steel wire
Weight: 10.0

==> All Sonoma Cooking Grids.

SGR30LP Heat Plates

CLA-MS0181

Click for photos

Bottom Flavor Grid for Sonoma model SGR30LP. Stainless steel. Made in USA.

Part Number: CLA-MS0181
Dimension Front-to-Back: 12”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 0.70

CLA-TS0182

Click for photos

Upper flavor grid for Sonoma model SGR30LP. Stainless steel. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

NOTE: Has unique underside, see photos.

Part Number: CLA-TS0182
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 1/2”
Material: stainless steel
Weight: 1.2

CLA-MS0085

Click for photos

Electrode heat shield for Sonoma model SGR30LP. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-MS0085
Dimension Front-to-Back: 16 13/16”
Dimension Side-to-Side: ”
Material: stainless steel
Weight: 0.4

SONHP1

Click for photos

Stainless steel Flavor Grid for Sonoma model SGR30LP.

Part Number: SONHP1
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 0.6

==> All Sonoma Heat Plates.

SGR30LP Igniter Components

10342-T12

Click for photos

21” wire for side burner or other applications. Both ends are female spade connector.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 10342-T12
Dimensions: 21
Weight: 0.05

IG-25B

Click for photos

Ceramic electrode with mounting bracket. For use with triple burner assembly part# SONT3 and ALTT3.

Sold individually, two (2) required
Use old screws and support plate

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-25B
Weight: 0.3

IG-30B

Click for photos

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

==> All Sonoma Igniter Components.

SGR30LP Valves, Orifices, and Manifolds

CLA-VB0245

Click for photos

Orifice for infrared burners with starter hole #63 if you need to drill the hole. Includes brass elbow with 1/4” compression fitting.

NOTE: If you need the orifice pre-drilled for Natural Gas or LP Gas, during check-out, in the message box, please state that you need the orifice drilled for Natural Gas #55 or for LP Gas #59.

Part Number: CLA-VB0245
Dimensions: 3 3/8” x 17 1/4”
Material: stainless steel and ceramic
Weight: 0.3

==> All Sonoma Valves, Orifices, and Manifolds.

SGR30LP Accessories

00270

Click for photos

Maple wood chips.

All natural wood smoke flavor
Great for use in BBQ's or smokers.
170 cubic inches (2 lbs. approx) in resealable bag

Try with portk, lamb, poultry, and fish.

Part Number: 00270
Weight: 1.3

43108

Click for photos

Polished stainless steel turner with an ergonomic soft grip grey handle and red accents. Great for flipping burgers or turning delicate fish fillets.

Part Number: 43108
Dimensions: 16
Material: stainless steel
Weight: 0.10

SR-7B

Click for photos

Universal 6 piece chrome plated skewer set. Designed so food does not rotate. Great for kabobs! 19 1/2” long.

Part Number: SR-7B
Dimensions: 19 1/2
Material: chrome steel
Weight: 1.0

00030

Click for photos

GrillPro EZ Check Gas level indicator. Accurate from -22° to 104°F. Magnetic back. Works on all sizes of tanks.

This tank gauge will monitor your propane level, while you grill, and let's you know when you're running low on gas.

The magnetic tank gauge offers fast, accurate propane level monitoring for any size LP tank. The magnetic backing makes it easy to attach, remove, and reuse across multiple tanks—perfect for grilling, camping, patio heaters, and more

Part Number: 00030
Weight: 0.1

CCR

Click for photos

Beer Can Chicken Roaster. Stainless steel.

Just place any 12 oz can into the center frame and put your spiced chicken cavity over the can and then put on the grill or oven, Infuses with flavors from various beverage in the can, Like Beer, Juice, Wine, etc. Your chicken will impart a different flavor! After use, the racks can be cleaned easily.

Part Number: CCR
Weight: 1.0

BRGG

Click for photos

Universal Grid Lifting Tool

Part Number: BRGG
Weight: 1.0

==> All SGR30LP Accessories.

BBQ Part Categories

Sonoma grill SGR30LP - Tuesday, May 12 2026

Return to Sonoma grill parts main page

More Sonoma grill models we have parts for
CGR27 \| CGR27LP \| CGR30 \| CGR30LP \| CGR30NG \| CGR44 \| CGR54 \| PF30LP \| PFISLP \| PFISNG \| PFSISLP \| SGIR27LP \| SGR27LP \| SGR30 \| SGR30MLP \|

*Orders for Sonoma grill model SGR30LP $49 and over ship free to the lower 48 states.
See shipping policy below for more info.

Home | About Us Contact Us | Privacy Policy | Return Policy | Shipping Policy |
Build Date: May 12 2026