Sonoma SGIR27LP Grill Parts

304 Stainless steel infrared rear rotisserie burner with ceramic wafer for Sonoma model SGIR27LP. For use with both liquid propane (LP) and natural gas grills. 8,000 BTU. Orifice not included. Use old orifice or purchase our orifice part# CLA-VB0245 that can be drilled for LP gas or natural gas.

Dimensions:

• Maximum overall length, including mounting tab on one end: 17”
• Maximum width: 3 3/8”
• Burner box 15 3/8” x 3 3/8”
• Mounting holes: 16 1/8” on center

Part Number: CLA-BL0229
Dimensions: 3 3/8” x 17”
Material: stainless steel and ceramic
Weight: 3.0

Stainless steel triple burner assembly set for Sonoma model SGIR27LP.

Part Number: SONT3
Dimensions: 17 13/16” x 18 1/2”
Material: stainless steel
Weight: 1.6

Stainless steel Z-Bar burner support bracket. Made in USA
This part is currently out of stock, but more are already on the way and expected to arrive mid May

Part Number: CLA-MS0116
Dimensions: 2” x 23”
Material: stainless steel
Weight: 0.70

Cooking grid not known for Sonoma model SGIR27LP. Our parts information for this grill model is incomplete, and we really don't know with certainty which cooking grid fits this model. It may be that we have the part but don't show it here due to data or other error.

If you know the original OEM part number, try searching for it in the search box at the top of this page.

You can also browse through all of the Sonoma cooking grids we carry. If we don't have the exact fit grid for your grill, we may have a suitable replacement part. Measure your existing part as well as the the grid support area of the grill so you'll know exactly what size grids will fit.

If you have this grill model and know the number and dimensions of your original cooking grids, please share this information with us. Click here to send an email to our GrillDr that includes this information. We greatly appreciate your help.

Part Number: CG-DUMMY
Weight: 1.0

Electrode heat shield for Sonoma model SGIR27LP. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-MS0085
Dimension Front-to-Back: 16 13/16”
Dimension Side-to-Side: ”
Material: stainless steel
Weight: 0.4

Bottom Flavor Grid for Sonoma model SGIR27LP. Stainless steel. Made in USA.

Part Number: CLA-MS0181
Dimension Front-to-Back: 12”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 0.70

Large Flavor Grid for Sonoma model SGIR27LP. Stainless steel. Only one of these are used on the grill. This part has an extended side that faces the infrared burner and acts as a heat shield. The other Flavor Grids do not have this shield.

• One required per grill.
• Sold individually.
• Made in USA.

NOTE: Sometimes shipped with protective vinyl peel-off coating. Remove before use. Made in USA

Part Number: CLA-TS0072
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 1.2

Stainless steel Flavor Grid for Sonoma model SGIR27LP.

Part Number: SONHP1
Dimension Front-to-Back: 15 3/16”
Dimension Side-to-Side: 5 7/16”
Material: stainless steel
Weight: 0.6

21” wire for side burner or other applications. Both ends are female spade connector.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 10342-T12
Dimensions: 21
Weight: 0.05

Ceramic electrode with mounting bracket. For use with triple burner assembly part# SONT3 and ALTT3.

• Sold individually, two (2) required
• Use old screws and support plate

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-25B
Weight: 0.3

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Orifice for infrared burners with starter hole #63 if you need to drill the hole. Includes brass elbow with 1/4” compression fitting.

NOTE: If you need the orifice pre-drilled for Natural Gas or LP Gas, during check-out, in the message box, please state that you need the orifice drilled for Natural Gas #55 or for LP Gas #59.

Part Number: CLA-VB0245
Dimensions: 3 3/8” x 17 1/4”
Material: stainless steel and ceramic
Weight: 0.3

GrillPro Texas hickory BBQ wood chips. 800g. For use in all BBQ Grill and smoker applications.

Part Number: 00220
Weight: 2.0

15” Stainless steel tong.

• Soft comfort grip
• Locking mechanism

Part Number: 40259
Dimensions: 15
Material: stainless steel
Weight: 0.14

Set of six 22” stainless steel V skewers with wood handles and silicone bezels. Silicone bezel helps the handle stay cool longer. V-shaped skewers keep food from spinning on shaft.

Part Number: 40538
Material: chrome steel
Weight: 1.1

Marinade Injector.

For injecting flavor and marinades into meat. Great for use with chicken, beef, pork, lamb etc. Disassembles for cleaning. Stainless steel injector tip. Graduated injection chamber. Easy to use and clean.

Part Number: 14950
Material: stailess steel
Weight: 0.5

Porcelain Coated Grill Topper.
11” x 16” Single draw construction for improved rigidity. Stainless steel handles and raised contours for improved functionality.

Part Number: 97122
Dimensions: 16” x 11 1/2”
Material: porcelain steel
Weight: 1.10

Stuffed Burger Press

The stuffed burger press is the best way to make gourmet stuffed and regular burger patties right at home. Easy to disassemble and clean.

Part Number: 24795
Weight: .3