Member's Mark CG2320401-MM Grill Parts

Stainless steel burner with electrode-mounting bracket for Member's Mark model CG2320401-MM. The bracket is not used on all grill models. If your model does not use a burner-mounted electrode, just ignore the bracket.

Part Number: 16251
Dimensions: 14 3/4” x 1”
Material: stainless steel
Weight: 0.6

Stainless steel cooking grids for Member's Mark model CG2320401-MM. SET OF THREE (3).

Part Number: 504S3
Dimension Front-to-Back: 16 1/2”
Dimension Side-to-Side: 35 5/8”
Material: stainless steel wire
Weight: 12.0

Stainless steel heat plate/ Flame Tamer for Member's Mark model CG2320401-MM.

Part Number: KENHP3
Dimension Front-to-Back: 14 15/16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 0.6

SET OF FOUR/4 PACK Stainless steel heat plate for Member's Mark model CG2320401-MM. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0193-X4
Dimension Front-to-Back: 14 15/16”
Dimension Side-to-Side: 3 3/4”
Material: stainless steel
Weight: 2.6

46” Wire with female spade connectors and square plastic connectors.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-30B
Dimensions: 46
Weight: 0.1

Burner-mounted ceramic igniter electrode with mounting bracket and hardware.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-20B
Weight: 0.05

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger.

• 1.5 volt
• Has four(4) spark outlets (male spade connector)
• Has two (2) male spade connectors for trigger (button) part #03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03344
Dimensions: 2” x 2 1/2”
Weight: 0.5

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

Round heat indicator.

• Single probe
• 3 1/8” diameter
• Requires .60” mounting hole

WARNING: Please remove your old heat indicator and inspect how it is fitted onto the hood of your grill. This heat indicator has a .44” thread length; a wing nut is included. The overall length of the probe from the base of the back-side to the end of the probe measures 1 1/2".

Part Number: 00020
Dimensions: 3 1/8” x 3 1/8”
Weight: .20

Fish Spatula. Stainless steel fish spatula with genuine rosewood handle. 18 1/2”. 10” spatula width.

Part Number: FS-1
Dimensions: 18 1/2
Material: stainless steel
Weight: 1.0

Basting brush with angled oak handle. 18” overall length.

Part Number: BB-5
Dimensions: 18
Weight: 0.8

18” long wood handle brass bristle grid brush with scraper and leather hang strap.

Part Number: WB-3
Dimensions: 18
Weight: 0.59