DCS DCS27A-BQRSSN Grill Parts

304 Stainless steel 15,000 BTU infrared rotisserie burner for DCS model DCS27A-BQRSSN. For use with LP and natural gas grills. Orifice not included. Use old orifice or purchase our orifice part number CLA-VB0245 that can be drilled for natural gas or LP gas

Dimensions:

• Maximum overall length, including mounting tab on one end: 20 7/8”
• Maximum width: 3 3/8”

Part Number: CLA-BS0250 (Replaces DCS DCS-210357)
Dimensions: 3 3/8” x 20”
Material: stainless steel and ceramic
Weight: 3.50

210358-R BURNER -27BBQ MAT PORC for DCS model DCS27A-BQRSSN.
Cast iron replacement ”H” burner. Fits older DCS 27” Professional Series grills.

Replaces original DCS burner part# 210358.

NOTE: Also fits grills manufactured by Dynamic Cooking Systems (DCS) for other brands.

Air shutter included.


Part Number: DCS-210358-R2 (Replaces DCS DCS-210358)
Dimensions: 16” x 6 1/4”
Material: cast iron
Weight: 10.0

304 Stainless steel 15,000 BTU infrared rotissierie burner for DCS model DCS27A-BQRSSN. For use with both liquid propane (LP) and natural gas grills. Includes collector box. Orifice not included. Use old orifice or purchase our orifice part number CLA-VB0245 that can be drilled for for natural gas or LP.

Dimensions:

• Maximum overall length, including mounting tab on one end: 20 7/8”
• Maximum width: 3 3/8”

Part Number: CLA-BS0358
Dimensions: 3 3/8” x 20”
Material: stainless steel and ceramic
Weight: 3.50

212425-SSHeavy duty stainless steel grill rack for DCS model DCS27A-BQRSSN. Fits DCS27 and DCS27A Professional Series gas grills by Dynamic Cooking Systems. Sometimes referred to as GRILL RACK - 27 BBQ.

• Replaces DCS factory part# 212425.
• Large diameter 5/16” stainless steel rods.
• Commercial grade 304 stainless steel.
• Sold individally.

Part Number: DCS-212425-SS (Replaces DCS DCS-212425)
Dimension Front-to-Back: 18 1/2”
Dimension Side-to-Side: 12 3/4”
Weight: 1.0

213524-R LAVA ROCK SUPP,27BQ.
Stainless steel Lava Rock support. This is a rack/tray for holding Lava Rock (not included). Requires one per burner.

Fits DCS 27” DCS27 and DCS27A Professional Series grills by Fisher & Paykel. These grills have the smaller 16” cast iron H burners.

• Replaces original DCS part# 30709-020.
• See part# 210005-R for Lava Rock.
• Sometimes shipped with vinyl peel-off coating. Remove before use.
• Made in USA
• Sold individually.

Part Number: DCS-213524-R (Replaces DCS DCS-213524)
Dimension Front-to-Back: 16 1/2”
Dimension Side-to-Side: 10 5/8”
Material: stainless steel
Weight: 2.2

210005-R LAVA ROCK.
Natural lava rock processed and screened for uniformity. For use with Support Rack/Radient 213524 and 213949.

NOTE: This is NOT a DCS product. The original DCS part was 4 pounds of Lava Rock. This is a 7lb bag manufactured by GrillPro.

Part Number: DCS-210005-R
Material: pumice
Weight: 7.5

DCS Electrode with wire.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: IG-37B (Replaces DCS DCS-210730)
Weight: 0.2

219343-R KIT, ROTARY IGNITER & KNOB BBQ.
Single outlet rotary igniter for DCS Professional Series grills by Fisher Pay& Kaypel.

• Replaces factory part# 219348
• Includes Igniter, knob, and mounting screws

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: DCS-219343-R (Replaces DCS DCS-219343)
Weight: 0.12

Type 1 LP Regulator with 22” Pressure Hose and 3/8” Female Flare Fitting.FITS: Up to 60,000 BTUs

Part Number: HR-4B (Replaces DCS DCS-210808)
Weight: 0.8

Brass valve for DCS.

• For LP and natural gas grills (see below)
• Off position D-Value: 12 o'clock
• Stem diameter: 8mm
• Orifice not included

NOTE: There is a set screw in the stem that allows this valve to be used in both LP or natural gas grills. The valve is shipped with the screw set in LP position. Turn the screw counterclockwise about seven turns for natural gas use.

Part Number: 30171 (Replaces DCS DCS-210733)
Dimensions: 3 7/16” x 1 5/16”
Material: brass
Weight: 0.3

Orifice for infrared burners with starter hole #63 if you need to drill the hole. Includes brass elbow with 1/4” compression fitting.

NOTE: If you need the orifice pre-drilled for Natural Gas or LP Gas, during check-out, in the message box, please state that you need the orifice drilled for Natural Gas #55 or for LP Gas #59.

Part Number: CLA-VB0245
Dimensions: 3 3/8” x 17 1/4”
Material: stainless steel and ceramic
Weight: 0.3

Cedar grilling planks adds a delicious wood-smoke flavor to foods grilled on them. Great for salmon! 11 7/8” x 5 1/4” x 5/16” 100% natural cedar. Two planks per pack.

Part Number: 00281
Dimensions: 11 7/8
Weight: .45

Meat Claws.

Shredding pork, chicken, or beef has never been easier. Spare the fork these meat shedding claws can hold with the larger outside tines and shred fine strands of meat with the smaller inside tines. Crafted of stainless steel with an easy to use grip that can be held multiple ways.
Each claw is 8.25 in. in overall length.

Part Number: 44070
Dimensions: 8 1/4
Material: stainless steel
Weight: 0.5

Universal 6 piece chrome plated skewer set. Designed so food does not rotate. Great for kabobs! 19 1/2” long.

Part Number: SR-7B
Dimensions: 19 1/2
Material: chrome steel
Weight: 1.0

Basting brush with angled oak handle. 18” overall length.

Part Number: BB-5
Dimensions: 18
Weight: 0.8

Roast holder. This holder is an ideal way to cook and also carry a roast from the grill. Made of heavy, bright nickel-plated steel, 15 1/4” L x 10 1/2” W.

Part Number: RR-3
Dimensions: 19 1/2
Weight: 1.0

Scrub brushes. Plastic grill scrubber. Cleans all types of cooking grids. Plastic grip handle.

Part Number: WB-7
Dimensions: 6” x 3 1/2”
Weight: 0.2