Nexgrill 720-0830A Grill Parts

Stainless steel tube burner for Nexgrill model 720-0830A.

Part Number: 10381
Dimensions: 15” x 1”
Material: stainless steel
Weight: 0.5

Stainless steel cooking grid for Nexgrill model 720-0830A. Sold as a set of two (2).

Part Number: 5S732
Dimension Front-to-Back: 17 3/16”
Dimension Side-to-Side: 26 3/8”
Material: stainless steel clad wire
Weight: 10.3

SET OF THREE/3 PACK Stainless steel heat plate/Flame Tamer for Nexgrill model 720-0830A. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0157-X3
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.16

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer for Nexgrill model 720-0830A. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use..

Part Number: CLA-TS0157-X4
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.88

Porcelain steel Flame Tamers for Nexgrill model 720-0830A. SET OF SIX.

Part Number: 97371-X6
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 3.3

Grillmaster Heat Plate for Nexgrill model 720-0830A.

Part Number: GMNGHP1
Dimension Front-to-Back: 14 1/4”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 0.81

Ignition module switch for spark generators that accept wired remote (button) trigger switches. Fits our spark generator part numbers 03322, 03332, 03344, 03352, 03356, 03387 and 03388.
Includes:

• Push-button ignition module switch with two male spade connectors on back
• Two 20” wires with female spade connectors
• One plastic mounting nut

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03152
Dimensions: 17 3/4” x 1”
Weight: 0.1

Battery powered ignitor/spark generator for Surefire electronic ignition systems using remote button/trigger switch.

Note: Some original ignitors (spark generators) that 03352 replaces had an integrated/built-in ground wire which is not present on this part (03352). If the ignitor you are replacing has an integrated/built-in ground wire, you will also need our ground wire part 03621. Inspect your system.

• 1.5 volt
• Has five (5) spark outlets (male spade connector)
• Has two (2) male spade connectors for the button/trigger switch part 03152 (sold separately)
• Uses a single AA battery (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 2 5/8”

NOTE: The battery cap is not a push button. The ignitor is fired by a remote button/trigger switch.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03352
Dimensions: 3 3/8” x 2”
Weight: 0.7

Ground wire required when replacing spark generator for a valve-triggered electrode with a remote switch-triggered spark generator. 03621 plugs into one switch inlet; ring connects to generator neck; switch wire plugs into the other generator switch inlet

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03621
Dimensions: 1 1/8” x 1 1/8”
Weight: 0.1

electrode

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 07370
Dimensions: 4 3/16” x 0 3/4”
Material: ceramic
Weight: 0.1

Heat indicator with a single probe and requires a 5/16” mounting hole. Note, the back side DOES NOT have an alignment pin.

Part Number: 00021
Dimensions: 3 5/8” x 1 3/4”
Weight: 0.2

Maple wood chips.

• All natural wood smoke flavor
• Great for use in BBQ's or smokers.
• 170 cubic inches (2 lbs. approx) in resealable bag

Try with portk, lamb, poultry, and fish.

Part Number: 00270
Weight: 1.3

Polished stainless steel turner with an ergonomic soft grip grey handle and red accents. Great for flipping burgers or turning delicate fish fillets.

Part Number: 43108
Dimensions: 16
Material: stainless steel
Weight: 0.10

Universal 6 piece chrome plated skewer set. Designed so food does not rotate. Great for kabobs! 19 1/2” long.

Part Number: SR-7B
Dimensions: 19 1/2
Material: chrome steel
Weight: 1.0

Deluxe 13” basting mop with hardwood handle and cotton mop head. Great for spreading BBQ sauces, marinades, and glazes on meat and poultry.

Part Number: 42055
Dimensions: 13
Weight: 0.2

Porcelain Coated Square Wok Topper.
12” x 12” x 2” porcelain coated grilling wok with stainless steel handles and perforations. The single draw design improves functionality and rigidity, it also makes it much easier to clean.

Part Number: 98121
Dimensions: 12” x 12”
Material: porcelain steel
Weight: 1.6

Stainless Steel Scraper for Phoenix and Holland Drip Trays

Part Number: SDDPS
Dimensions: 20
Weight: 0.30