Grillmaster 720-0697 Grill Parts

Stainless steel burner for Grillmaster model 720-0697.

Part Number: BMGKTB1 (Replaces Grillmaster 10000658A0)
Dimensions: 14 5/8
Material: stainless steel
Weight: 1.0

Cast iron cooking grids for Grillmaster model 720-0697. Porcelain treated, flat matte finish. Sold as a set of two (2).

Part Number: 60042
Dimension Front-to-Back: 17 1/4”
Dimension Side-to-Side: 26 3/4”
Material: matte cast iron
Weight: 14.0

Cast iron cooking grids for Grillmaster model 720-0697. Porcelain enameled, glossy finish. Sold as a set of two (2).

Part Number: 66342
Dimension Front-to-Back: 17 1/4”
Dimension Side-to-Side: 26 1/2”
Material: gloss cast iron
Weight: 10.1

Channel formed U-shaped porcelain steel cooking grids for Grillmaster model 720-0697. Channel formed means rolled steel stamped into a U-shape; is not solid round rods. Porcelain enameled, glossy finish. Sold as a set of two (2).

Part Number: 59812
Dimension Front-to-Back: 17 3/16”
Dimension Side-to-Side: 27”
Material: stamped porcelain steel
Weight: 7.2

Grillmaster Heat Plate for Grillmaster model 720-0697.

Part Number: GMNGHP1 (Replaces Grillmaster 04004007A0)
Dimension Front-to-Back: 14 1/4”
Dimension Side-to-Side: 3 3/8”
Material: stainless steel
Weight: 0.81

SET OF THREE/3 PACK Stainless steel heat plate/Flame Tamer for Grillmaster model 720-0697. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use.

Part Number: CLA-TS0157-X3
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.16

SET OF FOUR/4 PACK Stainless steel heat plate/Flame Tamer for Grillmaster model 720-0697. Made in USA.

NOTE: Sometimes shipped with vinyl peel-off coating. Remove before use..

Part Number: CLA-TS0157-X4
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: stainless steel
Weight: 2.88

Porcelain steel Flame Tamers for Grillmaster model 720-0697. SET OF SIX.

Part Number: 97371-X6
Dimension Front-to-Back: 14 9/16”
Dimension Side-to-Side: 3 1/4”
Material: porcelain steel
Weight: 3.3

Replacement electrode.

• Ceramic insulator
• 25” wire with female spade connector
• Locking nuts.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 01190 (Replaces Grillmaster 10001373A0)
Material: ceramic
Weight: 0.2

Universal battery powered push button ignitor.

• 1.5 volt
• Has five (5) terminals (male spade connector)
• Uses a single AA battery (not included))
• 03610 and 03620 wires are commonly used with this igniter (not included)
• Requires 7/8” mounting hole
• Overall dimensions: 2” x 3 3/8” x 3”
• Some original igniters had an integrated ground wire. Use wire part# 03620 for this purpose.

For more information about ignition systems and components, please see article Ignition 101 in our help center.

Part Number: 03380
Dimensions: 3 5/16” x 2”
Weight: 0.7

Stainless steel grease tray. Includes grease cup and grease cup holder. Made in USA.

NOTE: Install into back of grill with drain hole on right side.

Part Number: CLA-DS0219
Dimensions: 14 15/16” x 27 9/16”
Material: stainless steel
Weight: 4.9

Straight thru L.P regulator with 28” hose. Adequate to 90,000 BTU.

Part Number: HR-6B
Dimensions: 28
Weight: 1.50

7” cart wheel with 3/8” axel hole. Mini hub cap is # 00400251, sold separately.

Part Number: 10892-7G
Weight: .45

Alternative warming rack, stainless steel. Includes stainless mounting nuts and bolts. Made in USA

Part Number: CLA-WS0217
Dimensions: 7 5/16” x 26 15/16”
Material: stainless steel
Weight: 1.7

Universal rotisserie kit. Same as RK-MHP except with addition of longer 36” spit rod. Includes:

• R06 stainless steel motor
• SR-8 36” X 5/16” spit rod
• SR-5 31” X 5/16” spit rod
• BU-1 spit rod bushing
• PH-1 spit rod handle
• MH-1B Chrome-plated meat forks
• MB-3B Inverted motor mounting bracket and screws
• MB-2B Rotisserie bushing bracket (for grills with no bushing notch in casting)
• Maximum 25 lbs. balanced load

Fits grills with hoods up to 31 inches wide. Be sure to measure before ordering.

Note: The pre-drilled mounting holes in the MB-3B rotisserie motor mounting bracket are designed to accommodate existing hole patterns approximately 1 3/8” apart. It is possible that you may have to drill new holes.

NOTE: This kit does NOT include spit counter balance, which should be used to insure even weight distribution.

NOTE: Some of the parts in the kit are designed for a 5/16” rod. Rod SR-43, which is a 3/8” square rod, will not work with some of the parts in this kit.

Part Number: RK-MHP36
Weight: 4.6

Oval lid heat indicator. Three-hole mount with two threaded studs 1 1/2” offset on center. Requires 3/8” center hole for temperature sensor probe.

Part Number: 22551 (Replaces Grillmaster 05000572A0)
Dimensions: 2 15/16” x 1 7/8”
Weight: 0.2

Front clip-on shelf made specifically for Grillmaster model 720-0697 as an extra front workspace. Includes three pieces with nuts and bolts for assembly. Instructions included.

Dimensions:

• Side-To-Side: 26 7/16”
• Front-To-Back: 10 1/16”
• Height: 6”

Part Number: CLA-AS0218
Dimensions: 10 1/16” x 26 7/16”
Material: stainless steel
Weight: 3.45

Cast iron smoker box with six oblong venting holes. Designed to release wood smoke. Make sure this part will fit into your grill before ordering 8 3/8” x 5 1/4” x 1 3/8”.

Part Number: 00150
Dimensions: 5 1/4” x 8 3/8”
Material: cast iron
Weight: 3.90

20” Professional Extra Long Tong.
20” Stainless steel tong with red soft grip rubber inserts. Grip your food on the grill with ease. Manual lock saves on storage space.

This part is currently out of stock, but more are already on the way and expected to arrive mid August

Part Number: 40269
Material: stainless steel
Weight: 0.14

Universal Grid Lifting Tool

Part Number: BRGG
Weight: 1.0

Chrome plated rib/potatoe rack. Spaces up to 6 racks of ribs and 6 potatoes. Fits all grills. 12” x 7 1/4”.


Part Number: RR-2
Material: chrome steel
Weight: 1.0